Agaricus bisporus, Coprinus comatus, Agaricus Blazei Buds Management

First, the conditions of mushroom bud formation temperature is 15 °C ~ 22 °C, diurnal temperature difference is 8 °C ~ 10 °C, relative humidity of air is 80% ~ 90%, and to maintain a certain degree of scattered light and good ventilation. After the mycelium is full of material, it needs to be covered with soil to produce mushrooms. Therefore, the adjustment of water after the soil covering and soil covering is more important for accelerating the bud.
Second, the mattress cultivation and budding method When the mycelium full of material layer or long to mid-layer 2/3, cover 3 to 5 cm thick on the bed topsoil, cover soil before use to disinfect. After covering the earth for 1 day, then spray water. Spraying water should take a small number of times, that is, spray water 7 to 8 times a day. In 3 to 4 angels, the water content is kept at 18% to 20%. Water diversion can use 1% of clarified lime water or tap water. In the transfer of water, it is necessary to increase the amount of ventilation, and after the water transfer, the amount of ventilation should be appropriately reduced. Covering soil and diverting water can not only provide the temperature and humidity needed for the formation of mushroom buds, but also stimulate the kinks of the mycelium to form mushroom buds.
Third, the bags of soil covered with soil budding method When the mycelium covered the bag, remove the bag membrane, the fungus will be discharged on the bed of the mushrooming yard, bacteria from the 2 to 3 cm, the middle filled with fertilizer, when the bed After the raft is full, cover 3 to 5 cm thick loam. Cover the soil with water spray and humidity control, so that the soil moisture content is maintained at 18% to 20% covered with film insulation moisturizing, after every day to remove membrane ventilation, spray water to maintain air humidity, 10 to 20 days mushroom buds can be formed.
Fourth, after the formation of the buds, the growth of the buds should be given suitable conditions so that the buds can grow robustly. The temperature is maintained at 10 °C ~ 16 °C, the humidity is maintained at 85% ~ 90%, there is good scattering of light, there is fresh air, daily water spray moisturizing and ventilation. Before the buds differentiate, do not spray water directly on the buds. (Professor of Henan Agricultural University)

KDLED500 (2)


Germany imported beads

Imported French lens

mould Die-casting  Eight edge type Revolving arm

Optional emergency power supply≥3 hours

The main features:

1)Ideal cold light effects

Using the new LED cold light source, ensure energy saving and environmental protection and long service life up to 80,000hours and more.

The temperature increase of surgeon`s head below 1℃. LED do not engender infrared ray and ultraviolet radiation, without the temperature

rise and tissue damage caused by halogen shadowless light, also it can accelerate the wound healing after surgery, and without Radiation pollution.

With color temperature constant and soft, LED is very close to the sunshine.

1) Excellent shadowless effect

Lamp with the most scientific radian and Multi point light source design, ensure better uniform illuminance. When the lamps are partially occluded,

also can achieve perfect shadowless effect.Lamp panel radius of gyration ≥182cm, the lamp can be pulled to vertical floor, convenient to any angle illumination.

2) Excellent deep lighting

It is based on modularize method by Computer Aided Design, focused to irradiating with more beams of LED. It produces the deep lighting which beams

more than 1200cm,the illumination of center up to 180,000Lux or more, and offer the color temperature that can be adjusted from 3700K to 5000K which

is close to sunshine. Absolutely, it really reflects the color of human tissue and satisfied by all kinds of operating light needs.

3) Advanced control system

The use of liquid crystal display button control, to meet the needs of the medical staff of different patients with the brightness of the operation.

It offers illuminance memory function.

It does not effect using when a single circuit or one bulb is broken.

4) Universal suspension system

Rotating arm, a new type of alloy material is made of eight edge type.

Balanced system using imported arm module, more than 5 group universal joints, every cantilever must has more than 3 joints which can be rotated in 360°,

The structure is light, easy to manipulate, accurate positioning, can provide the maximum range of regulation.The equipped with fatigue correcting unit and

fix position hand handle device, easy to fix position after long time use.

5) Modern laminar lamp

The thickest part of lamp-chimney is not more than 10cm.

The lamp-chimney is made of ABS, The handle on the central of lamp can be detachable, can take high temperature (≤ 134°C) sterilization treatment,

easily adjust, flexible fixed.


Single Dome Operating Light

Single Dome Operating Light,Operation Theatre Lights,Single Head Operating Light,One Head Operating Lights

Shandong Kang'erjian Medical Technology Ltd. ,