The workflow of the baler:
The belt is sent to the position → the bundle signal is received → the brake is released, the main motor starts
(1)→The right top knife rises and stands against the right side of the skateboard
(2)→“T†type guide back
(3) → proximity switch senses the retracting probe
(4)→Main motor stop, brake pull
(5)→The strapping machine retracts the motor to rotate, and the belt is retracted for 0.35 seconds.
(6)→The strap is tightened and tied to the object.
(7)→Second start of the main motor, brake pull-in
(8)→The second swinging strap of the large swinging rod, tightening the strap
(9)→The left acrosome rises and compresses the lower layer
(10)→The heating piece extends into the middle of the two belts
(11)→The middle knife rises and cuts the belt
(12)→The top knife is lowered
(13)→The middle knives rise again, so that the two belts are firmly bonded
(14)→The middle top knife is lowered, and the left and right top knives are simultaneously lowered.
(15) → heating plate reset
(16)→Skipback
(17)→“T†type guide plate reset
(18)→Proximity switch senses the belt probe
(19)→The belt motor starts, and the belt is driven.
(20)→Large pendulum reset
(21)→The belt is in place, with the head on the “T†guide (22)→ proximity switch to the double probe
(23)→Main motor stop, brake suction
(24)→The baler completes a work cycle (end)
Nine items used by the baler:
1. Please confirm the power supply used by the machine, do not plug in the wrong power supply. This machine adopts three-phase four-wire system. The flower line is grounded neutral line for leakage protection.
2. Do not pass your head through the runway of the belt during operation.
3. Do not touch the heating pad directly with your hand. gzdt3kvt
4. Do not rinse the machine with water. When the workplace is wet, the operator should not work barefoot.
5. When the machine is not in use, please take the tape in the storage bin back to the reel to avoid deformation when using it next time.
6. Do not stick oil on the surface of the belt roller
7. Remember to unplug the power when the machine is not in use.
8. Do not replace the parts on the machine at will.
9. The main parts should be lubricated with oil frequently.
The belt is sent to the position → the bundle signal is received → the brake is released, the main motor starts
(1)→The right top knife rises and stands against the right side of the skateboard
(2)→“T†type guide back
(3) → proximity switch senses the retracting probe
(4)→Main motor stop, brake pull
(5)→The strapping machine retracts the motor to rotate, and the belt is retracted for 0.35 seconds.
(6)→The strap is tightened and tied to the object.
(7)→Second start of the main motor, brake pull-in
(8)→The second swinging strap of the large swinging rod, tightening the strap
(9)→The left acrosome rises and compresses the lower layer
(10)→The heating piece extends into the middle of the two belts
(11)→The middle knife rises and cuts the belt
(12)→The top knife is lowered
(13)→The middle knives rise again, so that the two belts are firmly bonded
(14)→The middle top knife is lowered, and the left and right top knives are simultaneously lowered.
(15) → heating plate reset
(16)→Skipback
(17)→“T†type guide plate reset
(18)→Proximity switch senses the belt probe
(19)→The belt motor starts, and the belt is driven.
(20)→Large pendulum reset
(21)→The belt is in place, with the head on the “T†guide (22)→ proximity switch to the double probe
(23)→Main motor stop, brake suction
(24)→The baler completes a work cycle (end)
Nine items used by the baler:
1. Please confirm the power supply used by the machine, do not plug in the wrong power supply. This machine adopts three-phase four-wire system. The flower line is grounded neutral line for leakage protection.
2. Do not pass your head through the runway of the belt during operation.
3. Do not touch the heating pad directly with your hand. gzdt3kvt
4. Do not rinse the machine with water. When the workplace is wet, the operator should not work barefoot.
5. When the machine is not in use, please take the tape in the storage bin back to the reel to avoid deformation when using it next time.
6. Do not stick oil on the surface of the belt roller
7. Remember to unplug the power when the machine is not in use.
8. Do not replace the parts on the machine at will.
9. The main parts should be lubricated with oil frequently.
Calcium Gluconate Tablet,Calcium Tablet,Calcium Tablet Product,Gluconate Finished Dosages
SHANDONG XINHUA PHARMACEUTICAL Co., Ltd. , https://www.sdxinhuapharm.com